Sorry, I'm new, but I checked around for a definitive answer on this, but I'm not 100% sure. Ignore you the control of parameters series.Ĭomplete equipment of simulation using LabView, Multisim, and MAX (easy answer accepted!) The same code works for the GPIB, series, or USB. There is no specific to USB example since one is not necessary. You just need to NI-VISA, especially if you plan on using LabVIEW, secondly, how weak is slow? Seconds, minutes? What command do you send to MAX? Third, your scope is a USBTMC device and is listed as such. What should I do to get the examples running for USB?įirst of all, there is no reason Tek-visa application must be installed.
(2) my scope is connected via USB and MAX sees, but all examples are for serial communication and I see no VI to the USB, but when you download the instrument driver, it said USB-compatible. Here is what I get (see the file attached jpg). (1) I can't rename the Max machine (I have installed TekVisa). Hi, I'm trying to set up my TDS 2014 C Tektronix oscilloscope, but I have a few questions: MAX does not allow me to rename the tektronix oscilloscope
We'll find the ACIP Pa$ $port is just a dll (two DLLs on my 64 bit OS, but the 64-bit version is 64-bit LabVIEW) who is on the PC at: C:\VXIPnp\WinNT\bin This interface is slower than the ACIP interface during the transfer of large data sets. With this interface, you can use a right TCPIP VISA resource. The alternative is to use the LXI(VXI-11) interface on the scope type.
I have not worked with RT stuff in a while, so I don't know how to install it. The LeCroy is configured to use the TCIP (ACIP) for remote connectionsĭo I need to install some software (such as the Teledyne LeCroy ACIP Passpor) on the PXIe8108 and if so how? System operating OR Real - Time PharLap 13.1 In MAX, I can add the oscilloscope under "My System" and "NO-PXIe8108". I checked that the LeCroy can ping my computer and PXIe8108. VISA: (Hex 0xBFFF0011) insufficient location information or the device or resource is not present in the system. The works of vi simple when it is running on the workstation, but not OR-PXIe8108.ġ073807343 error occurred while opening VISA in LeCroy_hello.vi I can see the oscilloscope in MAX and I can communicate using resources of e/s: 'VICP::169.254.103.3' in '169.254.103.1' work stations, but not the controller OR-PXIe8108 "169.254.103.2". I want to use an SMU-8108 with a RT operating system to access the LeCroy oscilloscope with VISAS through a local network. I have a LeCroy Waverunner 6050 A oscilloscope and I want to use it as a data acquisition equipment. Windows may unexpectedly turn off usb power The inititialize and narrow subVIs are called outside the Subvi. This VI is called at various points in the program do acquire a waveform.
I would like to know why this is happening and what can be done to remedy this. I know that this is not a matter of actual timeout because I tried increasing the timeout of 30 seconds, but the error always occurs immediately as soon as the function of reading or writing block is called.
I already read this page here:, but none of the solutions helped. Meanwhile if I stop the program, I can still bring up the oscilloscope in MAX and read and write commands him.
This happens even using subVIs new driver provided by OR (. After that happens once, all read or write functions also produce this same error for a while. However, I noticed that after a few hours, there are apparently random of chances that a VISA to read or write the block function will produce the error - 1073807339. My program is intended to be run for hours at a time, and it works perfectly as expected for the first few hours. I am trying to make measurements of waveform of an oscilloscope Tektronix 1052 B using LabVIEW. Error time-out random - 1073807339 using pilots of series Oscilloscope Tektronix TDS 200 1000 2000